this post was submitted on 20 May 2024
23 points (84.8% liked)

Linux

48067 readers
908 users here now

From Wikipedia, the free encyclopedia

Linux is a family of open source Unix-like operating systems based on the Linux kernel, an operating system kernel first released on September 17, 1991 by Linus Torvalds. Linux is typically packaged in a Linux distribution (or distro for short).

Distributions include the Linux kernel and supporting system software and libraries, many of which are provided by the GNU Project. Many Linux distributions use the word "Linux" in their name, but the Free Software Foundation uses the name GNU/Linux to emphasize the importance of GNU software, causing some controversy.

Rules

Related Communities

Community icon by Alpár-Etele Méder, licensed under CC BY 3.0

founded 5 years ago
MODERATORS
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
23
No internet in virtual machine (suppo.fi)
submitted 5 months ago* (last edited 5 months ago) by [email protected] to c/[email protected]
7 comments fedilink hide all child comments
 

I have on the host machine two network interfaces. One is lan and the other is a wlan. For libvirt I have created a nat network which is bound to the wlan. From the guest I can access other machines in the network host wlan is connected to. Also DNS lookup works. The problem is that there's no connection to the internet at all, e.g. pinging something gives "Destination network unreachable". ~~This only happens when both network connection on the host are active.~~ Running qemu/libvirt on OpenSuse Tumbleweed.

The nat network in question:

<network>
  <name>natToWlan</name>
  <uuid>a44c939c-e6bf-44d0-8f86-376056d418a4</uuid>
  <forward dev="wlp19s0f4u1u1" mode="nat">
    <nat>
      <port start="1024" end="65535"/>
    </nat>
    <interface dev="wlp19s0f4u1u1"/>
  </forward>
  <bridge name="virbr1" stp="on" delay="0"/>
  <mac address="52:54:00:1f:64:95"/>
  <ip address="192.168.100.1" netmask="255.255.255.0">
    <dhcp>
      <range start="192.168.100.128" end="192.168.100.254"/>
    </dhcp>
  </ip>
</network>
all 9 comments
sorted by: hot top controversial new old
[–] [email protected] 7 points 5 months ago

This only happens when both network connection on the host are active.

I'm not a networking expert by any means but this seems like a pretty strong hint that it's a routing issue.

Check the routing tables on the host? I'd bet that the internet is only reachable on the LAN interface (again, not an expert but one of them has to take priority, right?). I'm guessing that disconnecting the LAN interface changes the routing to go through the WLAN interface instead.

You could possibly add a static route to work around this: https://libvirt.org/formatnetwork.html#static-routes

[–] [email protected] 4 points 5 months ago* (last edited 5 months ago) (1 children)

Your routing table on the host changes when you have both networks active because the OS is preferring the NIC I'm guessing. You're using a static config for only one interface here.

Either switch to a static setup for NIC and Wlan, or create two interfaces for the VM that cover both host interfaces. A simpler setup would be host networking (macvtap) vs a bridged nat with only one path.

[–] [email protected] 1 points 5 months ago* (last edited 5 months ago)

This sounds reasonable. Curiously now that I tried again with both host lan & wlan active there was no problem. I have a hunch the routing depends on which interface networkmanger starts first.

$route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
default         192.168.102.1   0.0.0.0         UG    600    0        0 wlp19s0f4u1u1
default         RT-AC86U-6D60   0.0.0.0         UG    20100  0        0 enp15s0
192.168.2.0     0.0.0.0         255.255.255.0   U     100    0        0 enp15s0
192.168.100.0   0.0.0.0         255.255.255.0   U     0      0        0 virbr1
192.168.102.0   0.0.0.0         255.255.255.0   U     600    0        0 wlp19s0f4u1u1
192.168.122.0   0.0.0.0         255.255.255.0   U     0      0        0 virbr0_
[–] [email protected] 3 points 5 months ago

This is not great practice. You should get a dedicated Ethernet card for wlan and then block list the device on the host. The way your doing it is a little more complicated and is a security risk if the VM stops running for some reason.

[–] [email protected] 1 points 5 months ago

  • Your wlan

  • Your home lan

  • The internet

That makes three networks. Not two.

First, think about the way from the internet to your home lan. Is there NAT happening? Is there a DHCP server?

And then on the way from lan to wlan your server is doing NAT and DHCP again.

That doubling of NAT and/or DHCP is probably creating trouble.

[–] [email protected] 1 points 5 months ago

Have an idea which might solve this.

  1. Change the vm net config to NOT bind to specific host interface
  2. Change host networks so that there's only one default route (lan)
  3. Add routing to host that all traffic which goes to 192.168.102.x goes through the host wlan connection